Clutch

Talk about anything bike related.
Post Reply
User avatar
MR SLIKE
Reactions:
Posts: 204
Joined: 09 Jun 2015, 17:57
Location: Blackburn
Clutch

Post by MR SLIKE » 22 Oct 2016, 16:13

Hi all, just changed my clutch cable on my kawasaki z750 and now there's no tension the clutch won't engage at all, even when I manually push the clutch rod to the correct position soon as I put it in gear it jumps forward and stalls, any ideas guys as I'm stumped, cheers

Sent from my D5503 using Tapatalk

User avatar
cupidstunt
VIP
Reactions:
Posts: 684
Joined: 30 Mar 2015, 23:00
Location: walton upon sea Liverpool
Re: Clutch

Post by cupidstunt » 22 Oct 2016, 16:18

I take it that you have ajusted it properly at the lever end ?
:geek: HEAD PERVERT :geek:

User avatar
MR SLIKE
Reactions:
Posts: 204
Joined: 09 Jun 2015, 17:57
Location: Blackburn
Re: Clutch

Post by MR SLIKE » 22 Oct 2016, 16:43

Yeh all fitted, pulled through the new with the old cable, even when I manually push the clutch rod it still won't engage

Sent from my D5503 using Tapatalk

SMUDGER
VIP
Reactions:
Posts: 1327
Joined: 30 Mar 2015, 14:19
Re: Clutch

Post by SMUDGER » 22 Oct 2016, 22:35

changing just clutch cable shouldnt of effected the clutch , i find it strange you can engage clutch by pushing the clutch arm you must be very strong if im correct the force required to engage clutch couldnt be done by hand maybe wrong.

try this slacked off cable wind both clutch lever adjustment and clutch arm adjustment to there lowest, first turn clutch lever adjustment out few turns say 10mm out now finger press clutch arm in till it stops no force now tighten cable at clutch end till it holds the arm were finger push had it now go to lever pull lever should be tight and firm, if not id inspect clutch if so wind clutch lever adjustment in 2 turns. now push bike to a wall so front tyre is touching start bike clutch in put in first if it works adjust clutch lever adjustment to correct freeplay.

User avatar
MR SLIKE
Reactions:
Posts: 204
Joined: 09 Jun 2015, 17:57
Location: Blackburn
Re: Clutch

Post by MR SLIKE » 23 Oct 2016, 14:13

There's no engagement at all of the clutch, I found it a bit odd being able to push the arm, there's just nothing there at all, but before I changed the cable it bit without issue, just my old cable was at the max adjustment on the bars, propper stumped me this, looking like it's gonna have to go in I'm propper gutted

Sent from my D5503 using Tapatalk

User avatar
Trev
Reactions:
Posts: 66
Joined: 10 Aug 2016, 16:39
Location: Oldham
Re: Clutch

Post by Trev » 23 Oct 2016, 16:23

My guess would be the new cable is wrong.
Too long....?
This assumes it's fitted correctly.

User avatar
MR SLIKE
Reactions:
Posts: 204
Joined: 09 Jun 2015, 17:57
Location: Blackburn
Re: Clutch

Post by MR SLIKE » 23 Oct 2016, 20:11

Original kawasaki part, I checked the size, there's just no bite at all

Sent from my D5503 using Tapatalk

User avatar
Stumoores
VIP
Reactions:
Posts: 1018
Joined: 29 Mar 2015, 21:46
Re: Clutch

Post by Stumoores » 23 Oct 2016, 21:21

Sounds like it's fucked
Revving the bollox off it since 1982

User avatar
Marco
Reactions:
Posts: 149
Joined: 30 Mar 2015, 12:26
Re: Clutch

Post by Marco » 23 Oct 2016, 21:45

Unclip the cable from the clutch rod and you can twist the rod backwards and you should be able to pull the rod out so you can inspect it. My old zx6 went through a couple clutch rods

User avatar
rumpoldstilskin
VIP
Reactions:
Posts: 2042
Joined: 31 Mar 2015, 22:31
Re: Clutch

Post by rumpoldstilskin » 26 Oct 2016, 17:01

Lee are you saying you can actually engage the clutch by pushing the rod?

If so your clutch springs have gone or the cap to the basket/thrust bearing has worn through/snapped off.


Post Reply